English
العربية
Français
Deutsch
پارسی
Português
Русский
Español
The frequency of waterjet nozzle tube replacement in a waterjet cutting machine depends on several factors, including the type and thickness of the material being cut, the water pressure used, the quality of the abrasive used, and the number of hours the machine is in operation.
Description
Waterjet Nozzle Tube 10181113
Waterjet Nozzle Tube 10181113 is applied for SL-VI 50HP pump
Nozzle Tubes
| Nozzle Tubes | Description
| Nozzle Tubes | Description
| ||
| Actual in (mm) | Nominal in (mm) | Actual in (mm) | Nominal in (mm) | ||
| 10181113 | 2.65 (67.31) | 3.00 (76.20) | 10138451 | 8.65 (219.71) | 9.00 (228.60) |
| 10138402 | 3.65 (92.91) | 4.00 (101.60) | 05136023 | 9.15 (232.41) | 9.50 (241.30) |
| 10138410 | 4.65 (118.11) | 5.00 (127.0) | 10138469 | 9.65 (245.11) | 10.00 (254.0) |
| 10138428 | 5.65 (143.51) | 6.00 (152.40) | 05106224 | 10.15 (257.81) | 10.50 (266.70) |
| 05131784 | 5.91 (150.11) | 6.25 (158.75) | 05136031 | 10.65 (270.51) | 11.00 (279.40) |
| 10138436
| 6.65 (168.91)
| 7.00 (177.80)
| 05013735
| 11.65 (295.91) | 12.00 (304.80) |
| 10138444
| 7.65 (194.31)
| 8.00 (203.20)
| 05086913
| 14.65 (372.11) | 15.00 (381.0)
|
| 05106224 | 8.10 (205.74) | 8.45 (214.63) | |||
| 10138584 | 3.64 (92.46) | 4.00 (101.60) | 10138634 | 7.64 (194.06) | 8.00 (203.20) |
| 10138592 | 4.64 (117.86) | 5.00 (127.0) | 10138642 | 8.64 (219.46) | 9.00 (228.60) |
| 10138600 | 5.64 (143.26) | 6.00 (152.40) | 10138659 | 9.64 (244.86) | 10.00 (254.0) |
| 10138618 | 6.64 (168.66) | 7.00 (177.80) | 10138659
| 13.64 (346.46) | 14.00 (355.60) |
How often do nozzle tubes need to be replaced?
The frequency of waterjet nozzle tube replacement in a waterjet cutting machine depends on several factors, including the type and thickness of the material being cut, the water pressure used, the quality of the abrasive used, and the number of hours the machine is in operation.
The orifice, in particular, is a critical component that can wear down relatively quickly, especially if the machine is used for cutting harder materials or at higher pressures.
As a general rule of thumb, nozzle tubes should be inspected regularly, and the orifice should be replaced as soon as it shows signs of wear, such as a decrease in cutting performance or an uneven spray pattern. The frequency of replacement can vary widely depending on the factors mentioned above, but it is not uncommon for the orifice to need replacement after every 20-40 hours of use.
Other components of the nozzle tube, such as the mixing chamber and focusing tube, may also need to be replaced periodically due to wear or damage. The frequency of replacement for these components can vary depending on the specific machine and its usage, but it is typically less frequent than the orifice replacement.
Commentaires
Il n'y a pas encore de critiques.